Page tree

Versions Compared


  • This line was added.
  • This line was removed.
  • Formatting was changed.
Comment: Published by Scroll Versions from space DEV and version r0682

D toc

Microsoft Azure deployments can integrate with with the next generation of Azure Data Lake Store (ADLS Gen2).

Limitations of ADLS Gen2 Integration

  • This version requires a specific CDH 6.1 bundle JAR. Details are described later.

Read-only access

If the base storage layer has been set to WASB, you can follow these instructions to set up read-only access to ADLS Gen2. 


NOTE: To enable read-only access to ADLS Gen2, do not set the base storage layer to abfss.



  • The 
    D s platform
     has already been installed and integrated with an Azure Databricks cluster. See Configure for Azure Databricks.
  • For each combination of blob host and container, a separate Azure Key Vault Store entry must be created. For more information, please contact your Azure admin. 

  • When running against ADLS Gen2, the product requires that you create a filesystem object in your ADLS Gen2 storage account.
  • ABFSS must be set as the base storage layer for the 
    D s platform
     instance. See Set Base Storage Layer.

Create a registered application

Before you integrate with Azure ADLS Gen2, you must create the 

D s platform
 as a registered application. See Configure for Azure.

Azure properties

The following properties should already be specified in the Admin Settings page. Please verify that the following have been set:

  • azure.applicationId
  • azure.secret
  • azure.directoryId

The above properties are needed for this configuration.


Tip: ADLS Gen2 also works if you are using Azure Managed Identity.

Registered application role


NOTE: TheStorage Blob Data Contributor role or its equivalent roles must be assigned in the ADLS Gen2 storage account.

For more information, see Configure for Azure.

Key Vault Setup

An Azure Key Vault has already been set up and configured for use by the 

D s platform
. Properties must be specified in the platform, if they have not been configured already.

For more information on configuration for Azure key vault, see Configure for Azure.

Configure the 
D s platform

Specify CDH 6.1 bundle JARs


NOTE: For this release, use of the CDH 6.1 bundle JARs is required for ADLS Gen2 integration. Please specify all of these properties, even if you are not integrating with Hive.

Please complete the following steps to review and modify if necessary the bundle JAR properties and dependency locations.


  1. D s config
  2. Locate the following parameters and set them to the values listed below:


    NOTE: If you have integrated with Databricks Tables, do not overwrite the value for data-service.hiveJdbcJar with the following value, even if it's set to a different distribution JAR file.

    Code Block
    "hadoopBundleJar": "hadoop-deps/cdh-6.2/build/libs/cdh-6.2-bundle.jar",
    "spark-job-service.hiveDependenciesLocation": %(topOfTree)s/hadoop-deps/cdh-6.2/build/libs"
    "data-service.hiveJdbcJar": "hadoop-deps/cdh-6.2/build/libs/cdh-6.2-hive-jdbc.jar",
  3. Save your changes and restart the platform.

Define base storage layer

Per earlier configuration:

  • webapp.storageProtocol must be set to abfss.


    NOTE: Base storage layer must be configured when the platform is first installed and cannot be modified later.


    NOTE: To enable read-only access to ADLS Gen2, do not set the base storage layer to abfss.

  • hdfs.protocolOverride is ignored.

See Set Base Storage Layer.

Review Java VFS Service

Use of ADLS Gen2 requires the Java VFS service in the 

D s platform


NOTE: This service is enabled by default.

For more information on configuring this service, see Configure Java VFS Service.

Configure file storage protocols and locations


D s platform
 must be provided the list of protocols and locations for accessing ADLS Gen2 blob storage. 


  1. D s config
  2. Locate the following parameters and set their values according to the table below:

    Code Block
    "fileStorage.whitelist": ["abfss"],
    "fileStorage.defaultBaseUris": ["abfss://"],

    A comma-separated list of protocols that are permitted to read and write with ADLS Gen2 storage.


    NOTE: The protocol identifier "abfss" must be included in this list.


    For each supported protocol, this param must contain a top-level path to the location where

    D s platform
    files can be stored. These files include uploads, samples, and temporary storage used during job execution.


    NOTE: A separate base URI is required for each supported protocol. You may only have one base URI for each protocol.

  3. Save your changes and restart the platform.

Configure access mode

Authentication to ADLS Gen2 storage is supported for system mode only.


All users authenticate to ADLS using a single system key/secret combination. This combination is specified in the following parameters, which you should have already defined:

  • azure.applicationId
  • azure.secret
  • azure.directoryId

These properties define the registered application in Azure Active Directory. System authentication mode uses the registered application identifier as the service principal for authentication to ADLS. All users have the same permissions in ADLS.

For more information on these settings, see Configure for Azure.



NOTE: User mode, Azure AD, and Azure SSO are not supported for use with ADLS Gen2.


Please verify the following steps to specify the ADLS access mode.

  1. D s config
  2. Verify that the following parameter to system:

    Code Block
    "azure.adlsgen2.mode": "system",
  3. Save your changes.


Restart services. See Start and Stop the Platform.

After the configuration has been specified, an ADLS Gen2 connection appears in the Import Data page. Select it to begin navigating for data sources.


NOTE: If you have multiple ADLS Gen2 file systems or storage accounts, you can access the secondary ones through the ADLS Gen2 browser. Edit the URL path in the browser and paste in the URI for other locations.

Try running a simple job from the

D s webapp
. For more information, see Verify Operations.

  • Except as noted above, the ADLS Gen2 browser is identical to the ADLS one. See \ADLS Gen2 Browser.
  • Except as noted above, the basic usage of ADLS Gen2 is identical to the ADLS (Gen1) version. See Using ADLS.